How To Set Up Metal Shelves

If you buy something through our links, ToolGuyd might earn an affiliate commission.

Seville 5 Shelf Wire Storage System

I recently ordered 2 Seville 5-shelf wire shelving racks, assembled them over the weekend, and then ordered ii more. The second batch arrived today, and I put them together rather quickly – in about 15 minutes each.

I've assembled many wire shelving racks in the past few years, and the process has definitely gotten easier and quicker. Here are some tips I picked upwards along the mode.

1. Read the instructions

If you have never assembled wire shelving earlier, read the instructions. Make sure you empathize how it's supposed to get together.

In one case you lot've read the instructions, then consider the following tips.

Oh, and always make sure you accept all the needed parts before you start.

two. Don't attach the pole segments right abroad

Near taller wire shelving units, such every bit my half dozen-foot alpine ones, take 2-part poles that spiral together. Once I make sure I have the proper pieces, sometimes I will attach them together, other times I won't.

For today's wire shelving rack assembly, I did not connect the poles together starting time. I started with the lesser segments and installed 2 shelves before connecting the upper poles.

3. Start the kickoff shelf on its side

I start off by attaching the plastic brackets to the four poles – or bottom pole sections – for the lowest shelf while holding the shelf vertical.

Actually, no, the first thing I exercise is attach the caster wheels or leveling legs. And then I attach the first set up of shelf brackets.

Holding the shelf vertically, I and so insert the first 2 poles through the shelf support holes. I try to ensure that the shelf is reasonably secure effectually the plastic sleeves.

And then, I will weave the other ii poles through the upper holes of the shelf – the ones that are at the top of the vertically-oriented shelf.

If I accept a helper, I'thousand usually fine working with fully assembled poles. If information technology'south just me, I work with shorter half-length lesser poles.

I give those upper 2 poles a lilliputian twist to seat the plastic shelf supports a piffling more securely, then lower the shelf until all iv casters or leveling feet are on the floor.

And then, I will apply some weight or pressure on the corners of the bottom shelf, twisting the poles slightly. Or you could grab a deadblow hammer or rubber mallet, only I plant that the twist-and-press arroyo is more foolproof.

iv. Use the double-lines for guidance

Every wire shelving unit of measurement I have always assembled had single grooves, and also double grooves at regular spacings. These double lines make it a lot easier to install a shelf'south worth of plastic support brackets at 1 fourth dimension without measuring a thing.

5. Or use a height guess

If you desire the shelves to hold something in particular, such equally medium sized moving boxes, place 1 on a shelf as a top judge. Make sure at that place's plenty clearance and movement the detail around to each 4 corners to make sure your supports are all installed at the same tiptop.

6. A dead blow hammer or prophylactic mallet is great for seating shelves

Sometimes a quick whack with a dead accident hammer or prophylactic mallet tin better seat a shelf on its plastic supports.

Or… a sturdy workboot. Hey, I didn't ever have a healthy tool upkeep.

7. Ease shelves in place

If you slam a shelf downwardly on its plastic supports, there'southward a greater chance you'll knock a support out of place. When that happens, you'll take to lift the shelf, and concord it in place while you reattach the bracket halves.

Dropping a shelf onto its brackets too quickly tin can also lead to jamming, where one side drops quicker than the other. This can require a bit of effort to remedy, such as a quick upward strike with a rubber mallet.

Reader Tips

15 minutes each isn't bad, but if I wanted to movement quickly, I could probably assemble one of these 18″ x 48″ ten 72″ five-shelf wire shelving racks in near 10 minutes, maybe fifty-fifty less.

I don't know how long it took me to put together my commencement wire shelving units, simply I'm sure it was quite a fleck longer than 15 minutes. Hopefully these tips will help you become your wire shelving units quicker and easier.

For those of you who take assembled more than a couple of wire shelving racks yourselves,Practice y'all take any wire shelving rack assembly tips to share?

Final Tip

I have found that better quality wire shelving racks are ofttimes easier to gather. Pole sections thread together more easily, and the plastic shelf support bracket halves are better fabricated. Lesser brackets have thinner rings and slip more hands.

I have actually been liking Seville's wire shelving racks, which I ordered from Amazon. Previously I bought quite a few of their iv-shelf units, and now v-shelf wheeled units.

Purchase Now(via Amazon)